100Gb/s QSFP28 ZR4 Transceiver
Features
lCompliant with 100GBASE-ZR4
lSupport line rates from 103.125 Gb/s to 111.81 Gb/s OTU4
lLAN WDM EML laser and PIN receiver with SOA
lUp to 80km reach for G.652 SMF
lHot pluggable 38 pin electrical interface
lQSFP28 MSA compliant
lDuplex LC optical receptacle
lRoHS-10 compliant and lead-free
lSingle +3.3V power supply
lMaximum power consumption 6.5W
lCase operating temperature Commercial: 0 ~ +70℃ Extended-10 ~ +80℃
Industrial: -40 ~ +85℃
Absolute Maximum Ratings
It has to be noted that the operation in excess of any individual absolute maximum ratings might cause permanent damage to this module.
|
Parameter |
Symbol |
Min |
Max |
Unit |
Notes |
|
Storage Temperature |
TS |
-40 |
85 |
oC |
|
|
Power Supply Voltage |
VCC |
-0.3 |
4.0 |
V |
|
|
Relative Humidity (non-condensation) |
RH |
15 |
85 |
% |
|
|
Damage Threshold |
THd |
6.5 |
|
dBm |
|
Recommended Operating Conditions
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Notes |
|
Operating Case Temperature |
TOP |
0 |
|
70 |
oC |
commercial |
|
-10 |
|
80 |
extended |
|||
|
-40 |
|
85 |
Industrial |
|||
|
Power Supply Voltage |
VCC |
3.135 |
3.3 |
3.465 |
V |
|
|
Data Rate, each Lane |
|
|
25.78125 |
|
Gb/s |
|
|
Control Input Voltage High |
|
2 |
|
Vcc |
V |
|
|
Control Input Voltage Low |
|
0 |
|
0.8 |
V |
|
|
Link Distance (SMF) |
D |
|
|
80 |
km |
1 |
Notes:
- Depending on actual fiber loss/km (link distance specified is for fiber insertion loss of 0.35dB/km)
General Description
The transceiver is designed for 80km optical communication applications. This module contains 4-lane optical transmitter, 4-lane optical receiver and module management block including 2 wireserial inter- face. The optical signals are multiplexed to a single-mode fiber through an industry standard LC connector. A block diagram is shown in Figure
ModSeIL
The ModSelL is an input pin. When held low by the host, the module responds to 2-wire serial communication commands. The ModSelL allows the use of multiple modules on a single 2-wire interface bus. When the ModSelL is "High", the module shall not respond to or acknowledge any 2-wire interface communication from the host. ModSelL signal input node shall be biased to the "High" state in the module.
In order to avoid conflicts, the host system shall not attempt 2-wire interface communicationswithin the ModSelL de-assert time after any modules are deselected. Similarly, the host shall wait at least for the period of the ModSelL assert time before communicating with the newly selected module. The assertion and de-asserting periods of different modules may overlap as long as the above timing requirements are met
Optical Characteristics
The following optical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
|
Parameter |
Symbol |
Min. |
Typical |
Max |
Unit |
Notes |
|
Transmitter |
||||||
|
Lane wavelength（range） |
L0 |
1294.53 |
1295.56 |
1296.59 |
nm |
|
|
L1 |
1299.02 |
1300.05 |
1301.09 |
nm |
|
|
|
L2 |
1303.54 |
1304.58 |
1305.63 |
nm |
|
|
|
L3 |
1308.09 |
1309.14 |
1310.09 |
nm |
|
|
|
Signaling rate, each lane |
|
|
25.78125 |
|
GBd |
|
|
Side-mode suppression ratio |
SMSR |
30 |
|
|
|
|
|
Total launch power |
PT |
8.0 |
|
12.5 |
dBm |
|
|
Average launch power, each lane |
Pavg |
2.0 |
|
4.5 |
dBm |
1 |
|
OMA, each Lane |
POMA |
0.1 |
|
4.5 |
dBm |
2 |
|
Extinction Ratio |
ER |
6.0 |
|
|
dB |
|
|
Difference in Launch Power between any Two Lanes (OMA) |
Ptx,diff |
|
|
3.6 |
dB |
|
|
Transmitter and Dispersion Penalty, each lane |
TDP |
|
|
2.5 |
dB |
|
|
OMA minus TDP, each lane |
OMA-TD P |
-0.65 |
|
|
dBm |
|
|
Average launch power of OFF transmitter, each lane |
Poff |
|
|
-30 |
dBm |
|
|
Transmitter reflectance |
RT |
|
|
-12 |
dB |
|
|
RIN20OMA |
RIN |
|
|
-130 |
dB/Hz |
|
|
Optical Return Loss Tolerance |
TOL |
|
|
20 |
dB |
|
|
Transmitter eye mask {X1, X2,X3, Y1, Y2, Y3} |
|
{0.25, 0.4, 0.45, 0.25, 0.28, 0.4} |
|
|
||
|
Receiver |
||||||
|
Signaling rate, each lane |
|
|
25.78125 |
|
GBd |
|
|
Average Receive Power, each Lane |
|
-28 |
|
-3.5 |
dBm |
|
|
Receive Power (OMA), each Lane |
|
|
|
-3.5 |
dBm |
|
|
Receiver reflectance |
SEN1 |
|
|
-26 |
dBm |
for BER = 1x10-12 |
|
Receiver sensitivity Average, each lane |
SEN2 |
|
|
-28 |
dBm |
for BER = 5x10-5 |
|
Difference in Receive Power between any Two Lanes (Average and OMA) |
Ptx,diff |
|
|
3.6 |
dB |
|
|
LOS Assert |
LOSA |
-40 |
|
|
dBm |
|
|
LOS Deassert |
LOSD |
|
|
-29 |
dBm |
|
|
LOS Hysteresis |
LOSH |
0.5 |
|
|
dB |
|
|
Conditions of Stress Receiver Sensitivity Test (Note 4) |
||||||
|
Vertical Eye Closure Penalty, each Lane |
|
|
1.5 |
|
dB |
|
|
Stressed Eye J2 Jitter, each Lane |
|
|
0.3 |
|
UI |
|
|
Stressed Eye J9 Jitter, each Lane |
|
|
0.47 |
|
UI |
|
Notes:
- The minimum average launch power spec is based on ER not exceeding 9.5dB and transmitter OMA higher than1dBm.
Even if the TDP < 0.75 dB, the OMA min must exceed the minimum value specified here.
Digital Diagnostic Functions
The following digital diagnostic characteristics are defined over the normal operating conditions unless otherwise specified.
|
Parameter |
Symbol |
Min. |
Max |
Unit |
Notes |
|
Temperature monitor absolute error |
DMI_ Temp |
-3 |
3 |
oC |
Over operating temp |
|
Supply voltage monitor absolute error |
DMI _VCC |
-0.15 |
0.15 |
V |
Full operating range |
|
RX power monitor absolute error |
DMI_RX |
-3 |
3 |
dB |
|
|
Bias current monitor |
DMI_ bias |
-10% |
10% |
mA |
|
|
TX power monitor absolute error |
DMI_TX |
-3 |
3 |
dB |
Related products
$850.00 $790.00
100Gb/s QSFP28 ER4 40km Optical Transceiver
Features Hot Pluggable QSFP28 form factor Supports aggregate bit rate up to 103.125Gb/s LC Dupl...
Features Hot Pluggable QSFP28 form factor Supports aggregate bit rate up to 103.125Gb/s LC Duplex optical interface 4x25Gb/s LAN-WDM transmitter, EML laser,APD array detector Operating case temperature:0 to 70 °C Low power consumption <4.5W Applicable for 40km SMF connection without FEC All-metal housing for superior EMI performance IIC management interface Single +3.3V power supply RoHS compliant (lead free) Applications 100G Ethernet Other optical links Standards SFF8436,SFF...
$220.00 $200.00
100Gbps Single Mode 10KM QSFP28 Transceiver
100Gbps Single Mode 10KM QSFP28 Transceiver Description The100Gb/s QSFP28 LR4 transceiver is comp...
100Gbps Single Mode 10KM QSFP28 Transceiver Description The100Gb/s QSFP28 LR4 transceiver is compliant with the QSFP28 MSA and IEEE 802.3ba. QSFP28 LR4 transceiver modules are designed for use in 100 Gigabit Ethernet interfaces over single mode fiber. Feature Hot-pluggable QSFP28 form factor Supports 103.1Gb/s aggregate bit rates Maximum link length of 10km on Single Mode Fiber (SMF) Power dissipation < 3.5W Built-in digital diagnostic functions Built-in CIDR 4x278Gb/s DFB-based LAN...
$100.00
100Gbps Multimode 100Meter QSFP28 Transceiver DESCRIPTION The100Gb/s QSFP28 SR4 transceiver is...
100Gbps Multimode 100Meter QSFP28 Transceiver DESCRIPTION The100Gb/s QSFP28 SR4 transceiver is compliant with the QSFP28 MSA and IEEE 802.3bm. QSFP28 SR4 is an assembly of four full-duplex lanes, where each lane is capable of transmitting data at rates up to 25.78Gb/s, providing an aggregated rate of 103.125Gb/s. FEATURESFour-channel full-duplex transceiver25.78Gb/s data rate per channelMaximum link length of 70m on OM3(MMF) ,100m on OM4 (MMF)Power dissipation < 2.5WBuilt-in digital dia...